What is the role of steel floor steel floor

The all-steel floor is also called moving floor, computer room floor, all-steel elevated floor, anti-static floor. After high-quality steel plates are stamped and welded, they are made of high-strength, lightweight materials. High strength, waterproof, fireproof, moisture-proof performance, suitable for high-demand equipment room, program control room, monitoring room and so on.

All kinds of steel flooring

1, ceramic anti-static floor

The use of anti-static tiles as a surface layer, composite steel floor or cement particle board, surrounded by conductive rubber edge processing (the ceramic floor without plastic strips easy to fall away when bumping porcelain). It has the advantages of stable anti-static performance, environmental protection, fire protection, high wear resistance, high life (30 years of service life), high load (uniform load of 1200 kg/m2), waterproof, moisture resistance, and good decorative effect. Class room. The disadvantage is that the floor itself is heavier (a floor of 15kg or more), which has a certain influence on the load-bearing of the floor; in addition, professional installation workers are also required to install it, otherwise the installation will be uneven.

2, all steel anti-static floor (non-standard and national standard two)

The use of highly wear-resistant melamine HPL fireproof panels or PVC as the surface layer (in the northern part of the country because of the dry climate, it is not easy to use HPL fireproof panel veneers), steel shell structure base material, in addition to whether there are black plastic strips and there are no edges and edges The points.

General engineering companies choose non-standard types (difficulties in terms of conductivity and load carrying capacity, etc.) because of low prices. The use of national standards is required for high standards.

The advantages of the all-steel floor is that the construction is convenient, there is no gap problem after installation, and the replacement is convenient. The disadvantage is that the surface layer material is not wearable, the service life is short, and the skin angle is easy to change, and it will be replaced in a few years.

3, aluminum alloy anti-static floor

The product is made of high-quality cast aluminum. After being stretched and shaped, the surface layer is made of highly wear-resistant PVC or HPL veneer and electrically conductive adhesive. It has the effect that the substrate is not rusted and used repeatedly, thus effectively solving the composite floor. And all steel floor product defects, but tailor-made high-grade anti-static flooring, but its cost is too high.

4, all steel OA network floor

OA floor is a new type of floor building material. It is a ground decoration method designed to facilitate the expansion of the network of modern office rooms and office rooms. It solves many headaches that the designers have headaches in the traditional floor and the embedded wiring in the wall. Adapted to the specific requirements of the information automation technology in the intelligent building for the environment, making the various operating systems and control systems effectively linked together, high office automation, venues more comfortable, clean, beautiful, efficient, convenient and flexible.

Floor composition

The OA intelligent floor produced by our company is made of high-quality alloy cold-rolled steel sheet. After being stretched, it is spot-welded. The exterior surface is phosphatized and electrostatically sprayed. The inner cavity is filled with foamed cement and the four corners are provided with keyholes.

System assembly

The system consists of a floor, bearings, shock pads, and screws. The floor is placed on the support with a shockproof pad, and the screw is directly connected to the support through the corner hole around the floor. The support is galvanized and cast aluminum alloy structure, height adjustable and self-locking.

Features

1. All-steel structure, low product weight, strong bearing capacity and strong impact resistance;

2. The surface of electrostatic spray, soft light, wear-resistant, waterproof, fire, dust, corrosion, long service life;

3. High dimensional accuracy, good interchangeability, flexible assembly, easy maintenance, high repetition rate;

4. Outlet mold molding, easy wiring, ground socket installation is more convenient;

Use place

Mainly used in high-end (intelligent) office buildings, as well as offices in banks, taxation, industry and commerce, customs, insurance, and government buildings;

Steel Flooring - Specifications

All-steel floor is generally used in large and medium-sized computer rooms. All-steel floor can be used together with all-steel floor ventilation boards, making the static effects of all-steel flooring more prominent and more convenient to use. The size of the full steel floor can be adjusted according to different needs, but the common specifications of the general steel floor are: 600mm×600mm×30mm and 600mm×600mm×35mm.

  

All steel floor construction points

Installer

1. Floor treatment: Clean up all the garbage, dust, mud and other materials on the ground. If there is any bump on the ground, it must be filled or removed to keep the ground flat. The construction quality is better.

2. Estimate: Measure the site, estimate the number of installation items (including waste materials) for overhead floor, brackets, etc.

3, feeding: After the quantity is determined, feed in sequence

4. Selected benchmarks: Determine the construction benchmarks and follow the direction of the base construction.

5. Lay the base and floor: Lay the base and floor in order according to the base point direction.

6. Close the edge: When the wall, pillars, etc. can not be placed in a single block, you can cut edge processing.

7. Opening: The construction personnel shall open the hole according to the requirements and quantity.

8. Adjustment: After the completion of the entire project, the construction personnel will re-examine the situation. In case of defects, depending on the status adjustment floor, it is necessary to meet the requirements, and at the same time to protect the finished product to avoid surface damage.

Construction process

  

1, the installation of the floor

1.1 Measure the area of ​​the building and confirm that it is consistent with the blueprint. If not, do not construct and immediately consult with the owner or contractor to explain the nonconformity and correct it.

1.2 Verify that the height of all areas of the floor changes to facilitate the laying of the floor. Available construction level, theodolite or laser level test. At the same time, confirm the number and position of existing fixed structures such as columns and thresholds, and the height of the ground to the top surface. Lifters or floors must be fitted with the characteristics of certain areas, and special methods must be devised to ensure that the floor and the base are installed so that the floor has a certain level of fit. When the site conditions do not allow the floor to be installed horizontally and do not meet all structural requirements, do not rush to perform the construction so as not to affect the quality of the work after the construction.

1.3 Establish the starting point, according to the results of theodolite test, draw two vertical reference lines with the ink line to determine the starting position of the floor. In the edge position, the floor to be cut must not be less than 15cm and the base should be assigned 600X1200mm along the vertical line.

1.4 installed base, with a laser level as a benchmark, calibrate the base level, to ensure that in the range of three meters, the completion of the height level error shall not exceed ± 1.5mm, and the whole floor shall not exceed ± 2.5mm, and then Mounting base and die-cast aluminum head.

1.5 Install anti-static raised floor, install four floors along the ground, once again confirm that the floor and the base and the panel are perpendicular to the bottom line. If it is not vertical, it must be adjusted. On this basis, the overhead floor is installed accordingly.

2, cutting the surrounding floor

2.1 During the installation of the floor, the edge base can be used to support the side cut floor.

2.2 When each side of the cut floor is cut on the floor and walls, columns or other end surfaces, the floor must first be measured so that the cut floor can conform to and closely integrate with the outside of the wall profile, wall surface and cut The gap between good floors must be 1.5mm. When the floor needs to be cut irregularly to match the column or tube, it must be accurately measured to ensure that the floor and arc surface match. At the same time, make sure that all cutting floors must be fixed to the base (and additional bases if needed) and keep them level, flat and aligned.

3, installation of accessories

3.1 Install the specified floor accessories. The accessories must meet the design specifications and standards of the anti-static floor series.

3.2 Floor openings

The floor will be opened for many reasons. The company will use different decoration methods for different opening methods. Openings must be structurally complete, neat in appearance, free of sharp edges or burrs to prevent injury to personnel; wherever cut parts must use fire-protection foam. In the case where the floor hole is used as a ventilation hole, consideration must be given to the addition of a regulator so that the air can be adjusted.

Flooring Flooring Flooring Installation Decorative Cement Decorating Company Aluminum Alloy Doors Flooring Tiles Black Flooring Top Tiles Tiles Tiles Tiles Floor Tiles Tiles Tiles

Single Welding Hose mainly used for conveying of oxyen and acetylene gases for welding and cutiing equipment.The Welding Gas Hose has the characteristics abrasion resistant, weather resistant and ozone resistant. It is of pressure bearable, flexible, light in weight,anti-bending, less distortion and nice smooth surface.The burst pressure of our Rubber Welding Hose is 70kg and the temperature is -5℃-65℃.

 

Single Welding Hose

Welding Gas Hose,Rubber Welding Hose,Rubber Welding Gas Hose,Single Welding Hose

Zhanjiang QITAI Industry & Trading Co., Ltd. , https://www.qitaihose.com