Modeling smallpox construction notices modeling ceiling construction technology

Modeling smallpox has become an increasingly popular ceiling material. We know that in many places, the exterior design is critical, and the shape ceiling is exactly in line with this feature. Therefore, various high-end products have appeared one after another. What is the construction process of the ceiling molding ? , How to install the shape of smallpox, the following Xiaobian to introduce you!

First, the shape of smallpox construction precautions

1, before installation should first look at the site to see if there are no conditions to install the keel, mainly reflected in the wall is completed, whether the carpentry qualified, whether the plastering place is completed, some of the carpentry size must be required to do.

2, before the installation of the shape of the ceiling, we must first check whether the keel joints are firm and smooth, with the above sealing to do a good job, in the sprinkler with a sticky tape. When installing the modeling ceiling, first fix it from both sides of the middle, and pay attention to the installation size. The welding seam should be straight and the corners should be well controlled. After finishing the last four weeks, trim out the extra ceiling and look beautiful.

3, open hole lamp: Make a mark in the lamp hole, pvc ring accurate paste in the bottom of the soft film. Firmly remove excess lace.

4, in the construction site conditions permitting, according to the requirements of the design drawings of woodworking to do some fixed pvc special keel, angular position must be flat and smooth.

5. Air outlet and light pipe tray: Find the location of the air outlet of the air outlet. As with the surrounding area, install the soft film on the special keel for PVC. Note that the corner should be flat. After doing a good job, you can remove more of the smallpox.

6. Finally clean the shape of the ceiling with a clean towel.

7. Observe that the lighthouse, tuyere, and light pipe plate must be level with the surrounding keel, and they must be stable and stable without swinging.

8. Smoke, ceiling lamp, first positioning and then do a wooden chassis, the bottom of the wooden chassis to be polished smooth, and pay attention to the level, too low it is easy to highlight the traces of the chassis

Second, the construction of smallpox construction process

1. When installing undulations, each wavy bottom frame with the keel installed is consistent, so that after the flexible membrane is installed, the wavy shape is neatly coordinated.

2. The edge of the chassis that is in contact with the soft membrane must be smooth. After the installation, the ceiling of the ceiling is fixed. The ceiling of the ceiling is not flexible.

3. If there is a gap between the soft film and the soft film, the suspender and the main keel should be as thin as possible when lifting the underframe. Do covertly and neatly. Looking from the bottom up, you can't see the fixed base boom.

4, the installation of the shape of the ceiling pull film ceiling Lapon ceiling flexible ceiling light film shape ceiling art ceiling shower bath to be fully heated, especially in cold places, before opening the crystal wool to be heated to prevent the cold so that the soft film becomes brittle , damage to the soft membrane

5, install a circular shape ceiling film ceiling Lapon ceiling flexible ceiling light film shape ceiling ceiling ceiling when the bath, the flat code to use a bending machine bending. The arc is smooth and there is no cutting seam.

6, if you use the cutting method to bend, must be cut once every three centimeters, to be uniform, and can not cut more than half the thickness of the keel, otherwise it will appear prismatic.

7. When the time permits, install the keel first, measure the size, and then place the order, which can reduce many quality problems caused by improper modification or size.

Information on the construction of smallpox construction notices and the construction process of the smallpox has been introduced here. I hope this article will help you. If you still have something that you don't understand, you can leave a message for Xiaobian at the bottom. We will answer you as soon as possible.

Living room ceiling design Home living room design renderings

Living room decoration living room does not ceiling also look good

Plasterboard ceiling craft gypsum ceiling decoration effect chart

Led ceiling lamp led energy-saving lamps top ten brand rankings

Ceiling ceiling design ceiling installation led ceiling lamp

Engineering Veneer is a thin sheet of wood, rotary cut, sliced or sawed from expensive natural wood. The Veneer is easy to be edge jointed and overlaid on Plywood , MDF , particleboard and so on. So, it can be used in fancy plywood, fancy MDF, fancy Blockboard and veneer faced Particle board.We have Natural Engineering Veneer and Engineering Fancy Veneer

Luli Group Co., Ltd, also supply engineered wood veneers with good quality and competitive pricing.

Advantages of using veneers:

Compared to wood, one of the primary advantages of using veneer is stability. While solid wood can be prone to warping and splitting, because veneer is made of thin layers of wood glued together, the chances of splitting or cracking are reduced. Further, the glue used provides additional strength, making the end result stronger than natural wood.

Usages of Veneer:

Used to cover the surface of plywood, MDF, chipboard, blockboard and so on.

Specification details:

Sizes: 1220mm x 2440mm, 1250mm x 2500mm or as your request

Thickness: From 0.15mm to 0.6mm or as per request

Species: Okoume, Bintangor, Terminalia, Red hardwood, etc.

Grade available: A/A, A/B, B/B

Cutting way: Rotary cutting

Engineering Veneer

Engineering Veneer,Natural Engineering Veneer,Engineering Fancy Veneer,Engineered Wood Veneer

Luli Group Co.,Ltd. , https://www.cnluli.com